Repetier
About
- Username
- Repetier
- Joined
- Visits
- 2,088
- Last Active
- Roles
- Administrator
Comments
-
So it works now I guess. Can you say if you entered the 55 offset your self? It never happened to me that it was set other than 0 after creation. Also if you did this, what did you think what you are defining? Maybe the descriptions are not clear en…
-
Some printers with marlin will not do anything when sensor triggers unless they print from sd card, so these sensors are in that case useless. My sidewinder is one of them. So I unplugged the sensor from the printer and connected it to my raspberry.…
-
The problem as I already tried to describe is that your filament change solution is meant for a printer controlled lcd display where you can hit a button. Firmware blocks communication until filament is changed. It allows to continue with M108 but t…
-
Yes, but the folder system exists on all os, only on pi it is preset since we also provide special mount helpers so we know where it gets mounted in this case. For windows we don't know since it gets different driver letters depending on device.
-
> eventuell nächstes Update dann der Schriftzug "GPIO Pin" in "GPIO Pin (BCM)" umbenennen nicht zielführend. Das system ist für alle linux versionen und BCM ist die nummerierung des chips aber nur beim Pi heist die so weil der chip BCM... heißt. …
-
Normally printers do not stop on unknown commands, they just write it is unknown and server stops sending them from there on. In printer configuration->gcodes->Replacements you can add the rule ^G21$ and replace it with nothing. This will mak…
-
Hit button on printer to continue. Here it looks like it took to long and your printer does not send "busy" messages to tell it will not respond, so you got a timeout and server did send some commands. But nor buffer is full so printer does not see …
-
In printer menu go to "printer setup" - not printer configuration. There you can set a temperature offset and I guess it is not 0 in your case so server adds that to temperatures in your gcode.
-
Pi version only has 3 usb storage devices predefined for import. You can define them in global settings->folders easily your self.
-
Try activating ping-pong. Than print order is same as in OctoPrint. Otherwise server will try command sin parallel and with bad input buffer size that can cause problems, but these normally get fixed. But would not be the only printer requiring ping…
-
Ich glaube nicht das CuraEngine den Turm korrekt mit mehr als 2 Extrudern erstellt.Wichtig ist die Extruder 1,2,3 zu verwenden ohne lücken. Die Mischverhältnisse werden nicht von CuraEngine geändert, die müssen vorab von ihnen korrekt eingestellt we…
-
I'm running many prints lately on my prusa mk3s with original 3.9.3 without problems. I guess if it happens one special setting got wrong somehow, also I have no idea which could cause such prints.
-
Only permissions should define what you see. In a alter stage of server we want to make it more configureabal, but that is than for all users. More to optimize how you would iike it to be organized and what functions you want.
-
It will connect to known networks one it sees them. It will start with last network anyway and only go to hotspot mode if the active network is not reachable. You can also disable going to hotspot mode but should only do that if you have a display t…
-
1) we calculate that already our self so we are independent and work with all slicers. But you need to select the filament type so weight is correct. We plan a material management so that would be part of it then. 2) Adding what you have in queue is…
-
Sie mal hier: https://www.repetier-server.com/gpio-tutorial/ da steht auch das die pins BCM Nummerierung nutzen. Du kannst bei Tasten auch eine Webaction als ziel hinerlegen. Da server Befehle dazu gedacht sind im g-code eingebettet zu werden klapp…
-
Seit 1.0.4 kannst du auch gpio direkt über den server steuern. G-Codes kann man nur senden wenn der Drucker verbunden ist (grünes icon). Die Frage ist also läuft die Firmware über USB versorgt oder erst wenn der Strom an ist. Wenn er erst Hauptstrom…
-
One problem I see at the moment is that it seems I need to get the password. For security reason we never transmit the clear password and use a response challenge system to verify users. Especially since inside intranet you can not have trusted http…
-
With so much cards failing I'm not that sure it is the card. Also there exist many cards that claim to have more flash than they do. You normally only see this when file grows, but now you write to first 4GB. Question might be how big are your sd c…
-
Sieh mal hier ziemlich weit unten: https://www.repetier-server.com/knowledgebase/undervoltage-and-throtteling-of-pi/ da beschreiben wir wie man usb 5v abklemmt. Allerdings nicht wegen deines Problems. Versteh aber nicht ganz was hier das Problem sei…
-
You should upgrade to 1.0.4 for all the fixes being made. Not really sure what is going wrong here - looks a bit like under extrusion but for some moves it seems extrusion misses completely. Maybe not switched to relative extrusion while print is. E…
-
# ist Kommentarzeichen in linux Befehlszeile. Vermutlich stört es wenn man sagt der Rest der Zeile ist Kommentar und nicht Passwort. Aber ich muss es ja als parameter übergeben. Was mich mehr stört ist das du die Region immer neu angeben must. Hei…
-
Do you have version 1.0.4 - that is the first one where it exists. Should appear automatically on all linux versions. Eventually du a hrad reload in browser if it uses old web files.
-
No problem. And I see I was right that firmware requested it:-)
-
> But it seems whenever I try to bind 192.168.2.10 to it, I have problems. Ok how do you do that? Do you add that ip manually in wifi or ethernet as manual ip address? Is this ethernet or wifi? Did you set netmask correctly in that case on pi? F…
-
User table 2 looks formally ok. I wonder what 736 #else comes from. Could it prevent that table from being used at all? There must be a #if before and only if that is true the table will be included. And without correct table anything will be possib…
-
Yes, and as soon as I know what message it causes the faster I can help:-) You can change version in download link to download older versions.
-
Es gibt auf dem Startscreen für Filamentwechsel 2 abstände schnell und langsam. Schnell ist zum überbrücken von bowden einzügen um die lange distanz zügig abzuarbeiten. Langsam ist für den Rest wo das Filament auch aufgeheizt werdne muss bis es raus…
-
The API is incomplete in description. I'm currently rewriting it with better format and also more complete. At the moment best solution is to play in web gui with debug tools open. In network tab search the socket file (eventually reload when tab w…
-
You can always just install the previous version. Firmware stopped comes from printer and is a request to stop communication. So if that should stop what is the message firmware is sending that it wants to stop? Go to console to see what. Eventuall…