Repetier
About
- Username
- Repetier
- Joined
- Visits
- 2,088
- Last Active
- Roles
- Administrator
Comments
-
Yes, in printer settings you define scripts for different actions, one is print stopped, so add e.g. M140 S0 M104 S0 T0 To disable bed and first extruder. You can also add a move so head moves also out of the way.
-
Mit ssh auf dem pi einloggen. Das ist linux Befehl auf dem pi. Also dort eingeben. ssh ist ein Kommandozeilenprogram also in W10 einfach powershell öffnen und ssh pi@ipNummer dann Passwort raspberry angeben und schon bist du drin.
-
We have no official support for that board. Depending on which STM32 chip it contains we could add it to V firmware, but surely not in V1.
-
Did you install the PlatformIO extension in VSCode? That is all you need. After first compilation it will install the arduino libraries which you referenced here. mIt is no problem if vsc can not find the files Only important is if you can compile w…
-
Then I think it is marlin firmware.
-
https://ultimachine.com/products/mini-rambo-1-3 describes it as Arduino Mega board, not 32 bit and compatible with Rambo board, so yes, it is possible. When you run after connection M115 you should see what it is. Also the configuration.h file would…
-
Beim Netzteil würde ich mir erst sorgen machen wenn nach dem Problem ein vcgencmd get_throttlednicht 0x0 zurück liefert. Daran merkt man ob er mal Spannungsprobleme gemessen hat oder nicht. Bei dieser Art Hänger kann es theoretisch auch der usb seri…
-
Not distortion has own testing area #define DISTORTION_XMIN 10#define DISTORTION_YMIN 10#define DISTORTION_XMAX 190#define DISTORTION_YMAX 190 which was also wrong. G33 L0 will show current setting, but if it was ok first layer it is not a problem …
-
Sieh mal ob das dein Problem ist: https://www.repetier-server.com/knowledgebase/undervoltage-and-throtteling-of-pi/ Versuch insbesondere mal 5V vom Drucker abzuklemmen, damit dadurch keine Störungen entstehen. Das sieht so als ob Kommunikation auf …
-
Ja kann man. Sieh mal hier: https://www.repetier-server.com/knowledgebase/undervoltage-and-throtteling-of-pi/ Da beschreiben wir wie man den 5V pin vom usb abklebt damit der Drucker nicht mehr über USB mit Strom versorgt wird.
-
Make sure #define ENDSTOP_Z_BACK_ON_HOME 20 20 or something like that so it can also move a bit at the top. After homing M114 returns position that should be 0,0, z height above top. Adjust z length so this fits more or less and then move down appro…
-
You are right buster came after stretch. Thanks for the update. So the [all] missing prevented the overlay from being loaded.
-
Sehe gerade das F3 nicht klappt wenn man in der Zeile mit dem Treffer ist. Er sucht in der gleichen Zeile noch mal:-( Mit Shift+F3 kannst du bereits rückwärts suchen. Linien anklickbar geht leider nicht. Die Info ist nicht rückwert verkettet. Das …
-
Which server version are you using? Inter 64 bit? avrdude is bundled in server and it is starting /usr/local/Repetier-Server/modules/firmware/bin/avrdude Can you call it without arguments in the terminal? The strange part is the message from avrdu…
-
Use the same npm version, but sass is always a bit complicated as it includes c++ code from sass dependency I think. Can't say how often I also get stuck at sass parts when something goes wrong. Maybe better wait for next release - have updated a lo…
-
#define Z_PROBE_X1 15#define Z_PROBE_Y1 15#define Z_PROBE_X2 200#define Z_PROBE_Y2 15#define Z_PROBE_X3 15#define Z_PROBE_Y3 200 that is a rectangle for a cartesian printer. Your coordinates go euqally from negative to positive with 0,0 in the bed …
-
bekomme ich: --2019-12-11 12:06:29 Deine Uhrzeit war falsch. Zu dem Zeitpunkt ist das https Zertifikat nich gültig gewesen.
-
Das sind alles gcode Befehle also werden sie direkt an den Drucker gesendet. Der Drucker müsste bei den G4 S5 Befehlen jeweils 5 Sekunden warten und dann geht es weiter. So ist das ja auch manuell - 5 sekunden keine neuen Befehle und dann geht es we…
-
Ok, I see the 45° is in z direction not where I thought it was. Such a pattern can happen due to crosstalk if then the x end stop triggers without being hit. The shift is then away from the end stop. Can't say if that is the direction in your case. …
-
You mean the is only on /dev/fb... device on your pi? fb0 is the hdmi output. Our images are already on the newer stretch - so did it load the hyperpixel modules there?
-
As far as I see it is a framebuffer display. So it will not show what is on hdmi output which is programmed target of x server (framebuffer 0 /dev/fb0). Check if you have also /dev/fb1 which is your display. You must configure x to show it or copy f…
-
Repetier-Host does assume 1 unit is 1mm be default or the conversion unit defined it host Config->Units of imported Objects. I don't know inventor so can not say if it really exports stl in mm or if it has a factor. Guess you know better what fac…
-
crash detection is independent - it just rehomes xy and continues what I saw that correctly. power panic - it emits a signal that server can read and if you have recovery on in server you might be able to continue. Main probelm on reconnect is that …
-
That is the same resolution the default pi 7" display has which is what we also use. It just all appears a bit smaller if you have that resolution on 5".
-
Thanks. Good to know that marlin has also the option to be compiled with host support in mind. These are exactly the commands already implemented and well known.
-
Yes, most use z min for z probe just because it makes sense. Always check endstops false is often better so you get no false hits causing misalignment. Motors should stay on - often delta drop down when motor is off. You should also have #define E…
-
Home dir must be 1 for delta! Min software endstops can be true but are not really used on delta I think.
-
Yes, our firmware v2 supports the board and also the next server release has an uploader. Already used it with my board successfully. You can get an intermediate version by changing download name version with 0.93.2 - just make sure board is in dfu …
-
My Pharaoh has a RADDS board inside and that is a known board for due. If they have exchanged the board by a self made board I have no pins, but you can ask their support. You can also ask for firmware sources used.
-
The software endstops are wrong. You have either hardware or software endstop at max position but not both. Hardware endstop definition now looks good.