Repetier
About
- Username
- Repetier
- Joined
- Visits
- 2,088
- Last Active
- Roles
- Administrator
Comments
-
I would do both. The @nosize/@size improves the rendered images as renderer includes everything and that line is just a good way away, so makes the real object smaller.
-
That is too much trouble. I would need to include vlc or ffmpeg to do exactly your conversion. So it does not really gain anything except that you do not set the command. But then I would need to add configs. Interface shows webcam using img and th…
-
Check message I send you with email.
-
First forget slic3r offsets. Set them to 0! This was added long ago when firmwares did not have extruder offsets. Nowadays firmware handles the offset on it's own. Repetier-Firmware always did it on it's own. Having both just adds trouble and errors…
-
Yes, you can do it as well in the start gcode after heating up. That is completely ok. The original prusa profiles all do that.
-
No, sdcarddetect is not the problem. Check HAL.cpp line 662 and replace it with this volatile long __attribute__((used)) stepperWait = 0;it seems this solution works better. Compiler optimized the variable away.
-
Ja, host ist eigentlich fürs lokale Netz gedacht als Methode um Modelle zu slicen und schnell hochzuladen. Denke nächste Woche kommt das Update wenn nichts dazwischen kommt.
-
Ok, setting up a database is nothing I'd like to do. It just takes too much resources on a pi. But we have a sqlite database build in, so database function is no problem. I'd make one instance the server that needs to run all the time. Or uses says …
-
What firmware does the Alfawise use? Baudrate set correctly?
-
Data is stored in /var/lib/Repetier-Server and the volume containing that must be big. You can move it to an empty big folder and add a link there pointing to your decided position.
-
Der Server liest den webcam stream, speichert aber immer nur das letzte Frame. Wenn upload des letzten Bildes länger dauert, liest er das dann aktuelle Bild und sendet es als nächstes. Je nach Geschwindigkeit fehlen dann einige Frames. Wenn Verbindu…
-
Strange spot for a deviation.. Did you compare gcode to see if it is round there? Circles are always a bit of a problem regarding size, but normally look quite regular at least when printed. Also it is hard to see where it is not round. All I see i…
-
Yes, 7 is your printer with FTDI 232 chip. Works the same but these chips get a different name for serial ports. D you see it in the port list under /dev/serial/by-id/.. ? If not check if you have a /dev/ttypUSB... port. That is how they get named.
-
Checking what I did I saw I added another trick, so the purge line at y -3 does not get rendered and the object is better visisible. Here how I modified the start gcode @nosize{if not has_single_extruder_multi_material_priming};go outside print are…
-
Im Prinzip ist updated nicht schlechtes, aber man sollte sich bewusst sein, dass es zu Problemen führen kann, so dass nicht mehr alles funktioniert. Probleme die ich bereits hatte: - udev hat seine sicherheitseinstellungen geändert, wodurch flash mo…
-
Not so easy as heated chamber also uses different gcodes to control. Will think about a possible solution.
-
I never streamed to youtube, so my question - what is the advantage? I mean with port forwarding you can already watch webcam from anywhere. And second question - do you know if youtube accepts mjpg as input? As I said I never did any youtube stream…
-
You do it in the slicers gcode. There you also put your homing/preheating part so you can put your purge after that like it is done with original prusa printer profiles. Or you just add a skirt that has a minimum length, that is the slicer solution…
-
If you can parse the json string from panel due response you would have most of the informations you need.
-
RAMPS 1.5 is the same. It is just a revision with same pinout but different fuses/mosfets.
-
On delta use repetier-firmware:-) There buffer 16 gives more time then on marlin. Delta handling and transformation is done completely different normally giving much smoother moves and as planner can move over more segments less stuttering. Also com…
-
Ich hab mal 1 mit aufgenommen fürs nächste update, aber es muss eine ganze zahl sein. Was mjpg_streamer draus macht hängt davon ab, was die webcam liefern kann. Wichtiger ist die Auflösung. 640x480 mit raspi-cam liefern beispielsweise 2.2MB/s bei 1…
-
First question is if you know what manifold means. Watertight is just an easier to understand term but models need to be manifold so slicers know 100% what you intended. You can google for more infos on that. This model is quite complicated. Each of…
-
The E values are absolute in your example, so only differences get extruded. 0.85 is quite normal, 16 absolutely off so your steps per mm in firmware for second extruder must be factor 18 too low.
-
Nein das geht leider nicht. Aber im Webinterface geht das. Einfach auf jpg mit x Sekunden stellen. Wenn host darauf zugreifen kann geht das web interface ebenfalls von der Arbeit aus. mjpg geht auch vom host aus bei langsamer Verbindung. Der Server …
-
Have added it for next release 0.91.0
-
Also G29 reenables autoleveling it is not meant to be run for z height. Z homing is. g32 calibrates so homing computes the right Z by testing at a xy position and correcting for G32 tilt. Then with G29 you replace that with an average of 3 points co…
-
There is a thread here where the author of the TMC extension describes how to tweak RADDS to support them. You need some extra cables for chip select I think it was.
-
Yes, I revered direction as it was going in wrong direction to my standards on my device:-) Clockwise turns increase or go down in menu is the default. Also I like to hear you can select prints when starting with sd card, I can't:-( Tested with 2 d…
-
So HMI is just a display with controller communicating with gcode? In Repetier-Firmware you can have 2 serial connections in parallel and both can talk the same time to firmware. YOu just should not print from both or you get garbage. In config too…